1.0 Name: Drying hopper Volume: 60L Output: 50kg/h Heating power: 10kw Characteristics: protect the fan and electric heating tube. Famous brand electric elements and stable performance. Materials of the heating tube: 304 stainless steel without pollution and long service life. The sealing rings adopt the insulation silicone rubber. Â
2.0 Name: Single screw extruder (TD-LSJ50) Screw: --Diameter: Φ50mm; --L/D=25:1 --Screw material: 38CrMoAlA --Surface treatment of screw: hard chromium plating treatment; thickness of chromium coating: 0.5-0.6mm; hardness: HRC65 --Compression ratio: C/R=3.0 BM screw --Range of rotating speed: 10~80rpm --The design of screw is applicable to special rollers of ABS PLA PA plastic. --Treatment of internal and external surfaces of rollers. --Heater: the stainless steel heaterwith the internal surface receiving polished finish and the external surface of stainless steel. --The heating section and power: 3 heating sections, 1.8kw/section --Cooling of the roller: air cooling of high efficiency and low noise. --Cooling section and power: 3 cooling section. 120w/section. Reduction box: --hard tooth surface reduction box with spiral speed reduction transmission. --ZLYJ173 hard tooth surface helical tooth cylindrical gear reduction box, selection of 20CrMn Materials, malcomising the tooth surface receives gear-grinding machiing with the noise lower than 75Db and centrifugal lubrication of machining oil. --bearing brand: Japan "NSK" 3.0 Name: Driving motor: --AC "TECO" frequency converter, "Wannan" motor. 4.0 Name: Water channel (hot water channel and cold water channel) --Water channel specification: 304 stainless steel material, the thickness of stainless steel 2.0mm. --Circulating water device: 1 set of centrifugal pump with motor power 1.1kw, circulating water channel: 304 stainlees steel material, may be connected with the cooling device. --Water inlet pipe: "1/2" with stainless steel stop valve. --Water outlet pipe: "1/2" with stainless steel stop valve. 5.0 Name: Horizontal wire storage support --The length of wire storage support is 4.5m. --The gear motor of 0.75kw drives the magnetic power clutch to control the linkage of tension and wire-rewinding machine. --The winding speed is adjusted according to the length of stored wire and the largest length of stored wire is 80m. --The plastic wheel for wire storage >Φ120mm, wheel number 9+9, the wire storage wheel and shaft are installed with bearing to reduce the resistance. --The part of chain transmission is installed with safety protections.
	6.0 Name: Traction machine --Power: 0.4kw. --2 polyurethane wheels are assembled through pressure spring and sliding device. --Type of running 20: Φ120mm. 7.0 Name: Infrared ray diameter gauging device --Diameter measuring scope: 0.1~15mm. --Accuracy: +/- 0.05μm. --Measuring speed: 2*1200s/second. --The diameter measured can be displayed at the operation panel of the mainframe for the convenience of adjusting the speed of extruding machine or traction to ensure product diameter. --Able to test transparent and circular products. --Able to test the data of every surface of plastic wire comprehensively in a three-dimensional manner. 8.0 Name: Winding machine --Type: dual-shaft shallow shaft winding machine (the size of winding coil should be provided). --Power: 2.5kw/4P, "TECO" frequency converting control. --Flexible flat cable: Φ20 bar gathering stand. --"YAN MING" meter counter may set the forecast time and predicted output. The meter counter will alarm automatically when the predicted output is reached. --Applicable wire shaft: according to the requirement of customer's company. Â

	1.0 Name: Drying hopper Volume: 60L Output: 50kg/h Heating power: 10kw Characteristics: protect the fan and electric heating tube. Famous brand electric elements and stable performance. Materials of the heating tube: 304 stainless steel without pollution and long service life. The sealing rings adopt the insulation silicone rubber. Â
2.0 Name: Single screw extruder (TD-LSJ50) Screw: --Diameter: Φ50mm; --L/D=25:1 --Screw material: 38CrMoAlA --Surface treatment of screw: hard chromium plating treatment; thickness of chromium coating: 0.5-0.6mm; hardness: HRC65 --Compression ratio: C/R=3.0 BM screw --Range of rotating speed: 10~80rpm --The design of screw is applicable to special rollers of ABS PLA PA plastic. --Treatment of internal and external surfaces of rollers. --Heater: the stainless steel heaterwith the internal surface receiving polished finish and the external surface of stainless steel. --The heating section and power: 3 heating sections, 1.8kw/section --Cooling of the roller: air cooling of high efficiency and low noise. --Cooling section and power: 3 cooling section. 120w/section. Reduction box: --hard tooth surface reduction box with spiral speed reduction transmission. --ZLYJ173 hard tooth surface helical tooth cylindrical gear reduction box, selection of 20CrMn Materials, malcomising the tooth surface receives gear-grinding machiing with the noise lower than 75Db and centrifugal lubrication of machining oil. --bearing brand: Japan "NSK" 3.0 Name: Driving motor: --AC "TECO" frequency converter, "Wannan" motor. 4.0 Name: Water channel (hot water channel and cold water channel) --Water channel specification: 304 stainless steel material, the thickness of stainless steel 2.0mm. --Circulating water device: 1 set of centrifugal pump with motor power 1.1kw, circulating water channel: 304 stainlees steel material, may be connected with the cooling device. --Water inlet pipe: "1/2" with stainless steel stop valve. --Water outlet pipe: "1/2" with stainless steel stop valve. 5.0 Name: Horizontal wire storage support --The length of wire storage support is 4.5m. --The gear motor of 0.75kw drives the magnetic power clutch to control the linkage of tension and wire-rewinding machine. --The winding speed is adjusted according to the length of stored wire and the largest length of stored wire is 80m. --The plastic wheel for wire storage >Φ120mm, wheel number 9+9, the wire storage wheel and shaft are installed with bearing to reduce the resistance. --The part of chain transmission is installed with safety protections.
	6.0 Name: Traction machine --Power: 0.4kw. --2 polyurethane wheels are assembled through pressure spring and sliding device. --Type of running 20: Φ120mm. 7.0 Name: Infrared ray diameter gauging device --Diameter measuring scope: 0.1~15mm. --Accuracy: +/- 0.05μm. --Measuring speed: 2*1200s/second. --The diameter measured can be displayed at the operation panel of the mainframe for the convenience of adjusting the speed of extruding machine or traction to ensure product diameter. --Able to test transparent and circular products. --Able to test the data of every surface of plastic wire comprehensively in a three-dimensional manner. 8.0 Name: Winding machine --Type: dual-shaft shallow shaft winding machine (the size of winding coil should be provided). --Power: 2.5kw/4P, "TECO" frequency converting control. --Flexible flat cable: Φ20 bar gathering stand. --"YAN MING" meter counter may set the forecast time and predicted output. The meter counter will alarm automatically when the predicted output is reached. --Applicable wire shaft: according to the requirement of customer's company. Â

Injection Molding

Plastic Injection Molding Factory.We are advanced China Plastic Injection Molding manufacturers. Our Plastic Injection Molding manufacturing methods are extremely accurate and fast. They can provide unlimited rapid prototype plastic injection molding capabilities for a wide variety of high-volume products. The method is also used for low volume, high-quality plastic parts for everything from toy cars to giant television screens. Rapid prototyping is the process of designing and creating a new product or component using plastic injection molds. It is a critical process because it helps identify new product characteristics by testing them over again before a product goes to production.Plastic injection molds allow designers and engineers to create detailed models from digital designs that can then be brought to life into a physical product. This kind of design sharing provides a tremendous advantage for companies trying to reduce product development costs.
Many rapid injection molding tools include tools that are designed to assist the manufacturer with their overall production efforts. These tools can offer you a number of additional services including computer software designed to help you streamline your production efforts and increase your profitability. By streamlining your efforts, you can expect to see a significant increase in your production rate and efficiency.
RongNa offer OEM/ODM custom rapid prototype plastic injection tooling which can help you reduce the time necessary to create new parts and can save you valuable money on material costs.

The Finishing Option For Injection Molding

.Matte

.polished,

.sprayed,

.screen printing,

.pad printing,

.thermal transfer,

.water transfer,

.laser engraving,

.electrophoresis (water plating),

.vacuum coating,

.biting (etching, skin texture) for plastic molds

Advantages Of Plastic Injection Molding From RongNa
According to the customer's requirement to choose the Rapid tooling or the common mold,multi - cavities to save costs. Dozens of material and finishing options available.
analysis before quoting, also will suggest the better design way.
send the mold desgin for checking before tooling make.
Procuring parts on demand, without MOQ.
All products are inspected before shipment.

Injection Molding,Polycarbonate Injection Molding,Custom Injection Molding,Thermoplastic Injection Molding

Ningbo Rongna Technology Co.,Ltd , https://www.machiningcustom.com